directornoob.blogg.se - Import freescan into arc xt

#Import freescan into arc xt how to#
#Import freescan into arc xt serial#
#Import freescan into arc xt driver#
#Import freescan into arc xt manual#
#Import freescan into arc xt pro#

Learn more about mapping fields from floor plans to the geodatabase

#Import freescan into arc xt pro#

A template file is included with the ArcGIS Pro installation in the Resources\Indoors\MappingFile folder. Use the DWG or DGN format for the input CAD data.ĬAD file paths are stored in an Excel spreadsheet. When using an enterprise geodatabase, the connection file must connect directly to the database and the connection must be made as the database owner. This can be accomplished via Settings > Set C - Ch output.You can use this tool to load floor plan data into an indoor dataset created using the Create Indoor Dataset tool or an Indoors geodatabase created using the Create Indoors Database tool.

( XT Models) Be sure to disable control channel output before attempting to connect with FreeScan.

You may have to experiment to find the best setting for your system. On some systems using USB-Serial adapters this will improve communications reliability, on others it seems to decrease. 7E, you can turn off the Data Terminal Ready line. If you are using a USB-Serial adapter, try plugging it into a different USB port to get a lower COM port number. FreeSCAN does not always work with COM port numbers above 11.

If your COM port doesn't show, try using a lower COM port number.

#Import freescan into arc xt driver#

Insure that the USB driver you are using can handle the reduced speed.

It may also be necessary to reduce the COM port speed on your scanner.

#Import freescan into arc xt serial#

This slows down download speed by about 10% but helps prevent serial port errors with USB adapters and is enabled by default. To correct excessive errors during downloads, you should select "Use Careful I/O".If it is successful, return to the attempted function Note that this procedure is very slow, and may take some time to go through all combinations. It starts from 115200K and steps downward. If this doesn't work, allow the AUTO routine to detect the port and speed.You can use the TEST button to test your connection Try to manually select the COM port and speed using the top pull downs.There are a couple of things that can be attempted here This is the screen that you would see if you had errors during downloading, uploading or in the virtual scanner mode, and had clicked on 'Setup Com Port'.

#Import freescan into arc xt how to#

Most newer PCs have no serial ports, so you need to make the connection between the scanner and PC via an USB device.Please see our Connecting scanners via USB article for more information and tips on how to set this up properly.

#Import freescan into arc xt manual#

Scroll to Set Rear Port and press E/Yes.Ī Special note of Thanks to Mark's Scanner the 'Easier to Read' Manual series for these instructions and notes, website address is.

Scroll to Set Front Port and press E/yes.

Scroll to Set Serial Port and press E/yes.

Rear Port to the speed used to communicate with a GPS device, default is 4800bps.

Front Port to match the speed used to communicate with a PC, default is 115200bps.

Notes:You typically set the ports as shown directly below and it's "Highly Recommended" that you don't change this setup, as Firmware updates CANNOT be done via Rear Port, and will be used only for GPS connected devices.

Scroll to Set GPS Baudrate then press E/Yes.

Scroll to Set Serial Port then press E/Yes.

The fastest rate these scanners can handle is 115200bps

Scroll to Xfer Information and press E/Yes.

In all cases, The First & Second Step is to access the MENU and scroll to Settings, then:

Press L/O to auto return to normal scan screen (w/o having to press MENU multiple times to back-out of all Menus).

Press E/Yes to enter a level or accept a change.

Press MENU twice to go back a step/level.

On the Base/Mobiles, the MENU button is below the GPS key and above L/O on the left of the keypad, to Scroll through Menu items turn the Scroll Control wheel/dial, on the rightside of faceplate, the Silver large knob.

On most of the Handheld/Portables, the MENU button is the lower portion of the rubberized button on the left-side of the case, to Scroll through Menu items turn the Vol knob, on the top of the radio.Typically you will want to set it up 4800bps for a GPS unit, 115200bps for PC interfacing. Generally speaking, setting the fastest rate will insure the fastest transfer speed, To/From the Scanner/PC. You must set the Baud rate of the Port on the scanner.